Quick answer: Move your mouse quickly in circles inside the test box below. The tool counts how many position reports your mouse sends each second and shows the result in hertz (Hz). A standard office mouse reports at 125 Hz, most gaming mice at 1,000 Hz, and high-end models at 2,000 to 8,000 Hz. The test is free, runs in your browser and installs nothing. For the most accurate reading use Chrome or Edge and keep moving for at least five seconds.
Move your mouse fast in circles inside this box
Use this mouse polling rate test to check whether your mouse is really delivering the rate printed on the box, to confirm that a setting you changed in the manufacturer’s software took effect, or to diagnose a cursor that feels jumpy. The sections below explain how to read the result, what polling rate means, how to change it and how to fix a mouse that reports lower or less stable numbers than it should.
How to use the polling rate checker
- Place the cursor inside the dashed test box above.
- Move the mouse quickly in wide circles or figure eights. Slow movement produces fewer reports, so speed matters.
- Keep moving for five to ten seconds and watch the three numbers settle.
- Read the Average Hz value and the closest standard rate shown under the box.
- Click Reset test before checking another mouse or another setting.
The three readings mean different things. Current Hz is the live rate over the last fraction of a second. Average Hz is the mean of all valid samples since you started. Peak Hz is the highest sample, which is usually the closest to the mouse’s configured rate, because a mouse only sends reports while it is moving fast enough to have something new to report.
What is mouse polling rate?
Polling rate is how many times per second your mouse reports its position to the computer. It is measured in hertz. At 125 Hz the PC receives a new position every 8 milliseconds. At 1,000 Hz it receives one every millisecond. A higher rate means the cursor position on screen is based on fresher information, which reduces input delay and makes fast movements look smoother.
| Polling rate | Time between reports | Typical device |
|---|---|---|
| 125 Hz | 8 ms | Office mice, most Bluetooth mice |
| 250 Hz | 4 ms | Older gaming mice, battery-saving modes |
| 500 Hz | 2 ms | Entry-level gaming mice |
| 1,000 Hz | 1 ms | Standard for gaming mice |
| 2,000 Hz | 0.5 ms | Enthusiast wireless mice with a high-speed dongle |
| 4,000 Hz | 0.25 ms | High-end competitive mice |
| 8,000 Hz | 0.125 ms | Flagship wired and wireless esports mice |
Polling rate is not the same as DPI. DPI, or CPI, is sensitivity: how far the cursor travels for each inch the mouse moves. Polling rate is how often that movement is reported. You can run 400 DPI at 8,000 Hz or 16,000 DPI at 125 Hz. They are independent settings.
What is a good polling rate?
- Office work and browsing: 125 Hz is enough. You will not see a difference on a 60 Hz monitor.
- Casual gaming: 500 or 1,000 Hz. The step from 125 to 1,000 Hz is the one most people can feel.
- Competitive shooters on a 144 Hz or 240 Hz monitor: 1,000 Hz as a baseline, 2,000 or 4,000 Hz if your PC handles it without frame drops.
- 360 Hz and faster monitors with a high-end CPU: 4,000 or 8,000 Hz can make tracking fractionally smoother.
Returns diminish quickly. Going from 125 to 1,000 Hz removes up to 7 milliseconds of delay. Going from 1,000 to 8,000 Hz removes less than 1 millisecond. Very high rates also cost processor time, because the PC must handle up to eight thousand interrupts a second. On a mid-range CPU that can lower frame rates or cause stutter in some games, which hurts more than the extra reports help.
How to change your mouse polling rate
Windows has no polling rate setting of its own. The rate is set in the mouse, through one of these routes:
| Brand | Where to change it |
|---|---|
| Logitech | Logitech G HUB, select the mouse, Sensitivity tab, Report rate |
| Razer | Razer Synapse, Performance tab, Polling rate |
| SteelSeries | SteelSeries GG, Engine, select the mouse, Polling rate |
| Corsair | iCUE, Device settings, Polling rate |
| Glorious, Pulsar, Lamzu and similar | The brand’s desktop or web configuration tool |
| Mice without software | A button on the underside, or a button combination described in the manual |
After changing the value, come back to this page, click Reset test and run the mouse Hz test again to confirm the new rate is active. Settings are usually stored in the mouse’s onboard memory, so they follow the mouse to another PC.
Why your result may be lower than expected
If your gaming mouse is set to 1,000 Hz and the test shows 500 or less, work through this list.
You are not moving fast enough
A mouse sends a report only when the sensor detects movement. Slow motion yields gaps between reports and a low reading. Use fast, continuous circles.
The browser is limiting the measurement
Chrome and Edge expose raw pointer events, which lets a web page see every report. Firefox and Safari deliver mouse events in step with the screen refresh, so a web test can underestimate high rates in those browsers. Background tabs and battery saver modes also throttle events.
The mouse is on Bluetooth
Bluetooth mice typically report at 125 to 133 Hz regardless of what the sensor can do. To reach 1,000 Hz or more, use the 2.4 GHz USB receiver or a cable.
The USB connection is poor
Hubs, front-panel ports, KVM switches and long extension cables can cap or destabilize the rate. Plug the mouse or its receiver directly into a port on the motherboard. Rates of 4,000 and 8,000 Hz usually need a USB 3 port and the dongle supplied for that purpose, placed close to the mouse.
Power saving is interfering
Open Device Manager, expand Universal Serial Bus controllers, open each USB Root Hub, and on the Power Management tab clear “Allow the computer to turn off this device to save power”. In Power Options, set USB selective suspend to Disabled.
The PC is under heavy load
If the processor is at 100 percent, reports arrive in uneven bursts. Close heavy programs and test again. Unstable readings that jump between very different values usually point to load, wireless interference or a low battery.
Drivers or firmware are out of date
Update the mouse firmware through the manufacturer’s software, and install current chipset and USB drivers from your motherboard or laptop maker.
Windows settings that affect mouse feel
Polling rate is one part of how a mouse feels. These Windows options matter as much.
- Enhance pointer precision: this is mouse acceleration. For consistent aim, turn it off in Settings, Bluetooth and devices, Mouse, Additional mouse settings, Pointer Options.
- Pointer speed: leave the Windows slider at the middle position (6 of 11) and adjust sensitivity with DPI instead, so no movement data is skipped or doubled.
- Refresh rate: confirm your monitor is actually running at its maximum in Settings, System, Display, Advanced display. A 144 Hz monitor left at 60 Hz hides most of the benefit of a fast mouse.
- Game Mode: keep it on in Settings, Gaming. It reduces background activity while a game is running.
- Windows version: Windows 11 received specific fixes for stutter caused by high polling rate mice in games, starting with the mid-2023 updates. If you game with a 4,000 or 8,000 Hz mouse on an old build, updating is worthwhile.
Windows 10 no longer receives these improvements, because its support ended on 14 October 2025. If your gaming PC still runs it, moving to Windows 11 keeps you on current input, graphics and security updates. A Windows 11 Pro key is $11.99 and a Windows 11 Home key is $9.99 at GetDigiMarket. Our guide on how to download, install and activate Windows covers a clean installation, and essential Windows 11 tips lists the settings worth changing afterwards. If you are deciding between editions for a gaming PC, read Windows 11 Home vs Pro.
Wired vs wireless polling rate
Modern 2.4 GHz wireless gaming mice match wired mice at 1,000 Hz with no practical delay. Above that, the differences are battery life and placement. A wireless mouse at 4,000 Hz can drain its battery three to four times faster than at 1,000 Hz, and it needs the receiver within about 30 centimeters with a clear line of sight. Many players keep 1,000 Hz for everyday use and switch to a higher rate only for competitive sessions.
Is this polling rate test accurate?
A browser-based test measures the events the operating system and browser deliver to the page. In Chrome and Edge that tracks the true rate closely up to 1,000 Hz and gives a good indication above it. For laboratory precision at 4,000 and 8,000 Hz, a native program that reads raw input directly is more exact. For the questions most people have, such as “is my mouse at 125 or 1,000 Hz?” and “did my setting apply?”, this test gives a clear answer in seconds.
Frequently asked questions
How do I test my mouse polling rate?
Move the mouse quickly in circles inside the test box on this page for five to ten seconds. The Average Hz and Peak Hz readings show how many reports per second your mouse sends.
What is a good mouse polling rate for gaming?
1,000 Hz is the standard and is enough for almost every player. 2,000 to 8,000 Hz offers a small extra improvement on high refresh rate monitors with a fast processor.
Is 8,000 Hz better than 1,000 Hz?
It reduces the report interval from 1 millisecond to 0.125 milliseconds, a difference few people can feel. It also raises CPU load and wireless battery drain, and can cause stutter in some games.
Why does my mouse show 125 Hz?
Office mice and Bluetooth connections usually run at 125 Hz. A gaming mouse may also be set to 125 Hz in its software or by a button on its underside.
Does polling rate affect FPS?
It can. Very high polling rates increase processor work, which may lower frame rates or add stutter on slower CPUs. If that happens, drop to 1,000 Hz.
How do I change my mouse polling rate in Windows 11?
Windows has no setting for it. Use the manufacturer’s software, such as Logitech G HUB or Razer Synapse, or the polling rate button on the mouse.
Is polling rate the same as DPI?
No. DPI is sensitivity, meaning how far the cursor moves per inch. Polling rate is how often the mouse reports its position.
Can I test polling rate on a laptop touchpad?
Yes. The test box responds to any pointing device. Touchpads usually report between 60 and 140 Hz.